Complete Steps Related to How to Repair a Dry Battery

Maintaining a dry battery is actually easier. However, there are times when the dry battery is drained and needs to be repaired. Here are some easy ways to repair a dry battery.

Prepare the Tools and Materials Needed

There are several tools and materials that you need to prepare before starting to repair the dry battery independently. Here is a list of the tools and materials provided:

Buy battery water or zuur intended for filling new batteries and not battery water for adding or refilling battery fluid
Provide a tool such as a prying tool or you can use a flathead screwdriver intended to open the battery cover on the top side
Prepare plastic glue or a hot glue gun or you can also use sealant that is useful for reattaching the battery cover
Prepare or buy a printer ink syringe or similar that is useful for injecting zuur water or battery water into the dry battery box
Finally, also prepare a cloth that functions to wipe off any liquid droplets that may fall during the repair

Remove the Battery from the Car

After preparing the necessary tools and materials as explained above, the next step in repairing the drained dry battery is to remove the battery from the car box.

The method is very easy, to properly remove the battery, make sure the car engine is off first. Then the sequence is to first remove the negative terminal from the battery, and only then remove the positive terminal. Make sure the order of removing the negative and positive terminals is correct to avoid short circuits or electrical connections.

Clean the Dry Battery

After successfully removing the dry battery from the car, it is advisable to clean the outer part of the dry battery first. The purpose of cleaning the outer part of the dry battery is to ensure that dirt sticking to the dry battery does not fall onto other parts of the battery that could endanger it. Cleaning the dry battery is quite easy because you only need to wipe the dirty outer part of the battery with a dry cloth.

Disassemble the Cover of the Dry Battery

A quick way to repair a dry battery that runs out or is having problems is to first disassemble the cover of the dry battery until it is open. To open the dry battery cover, you can use a screwdriver carefully. You should know that the dry battery cover is quite hard, so it will not open easily.

Fill Zuur or Battery Water into the Dry Battery

Check the condition of the dry battery to see if the rubber holes are fully open. Generally, there are three to ten rubber holes adjusted based on the current capacity or ampere of the dry battery. Next, prepare the syringe and cloth to avoid any liquid falling onto other components. The zuur battery water is inserted into the syringe. Then, insert the zuur battery water into each hole in the battery. The position of inserting the syringe should be up to a depth of 1 cm from the battery hole. Repeat this method for all rubber holes and then close the rubber holes again.

Reattach the Cover of the Dry Battery

The next step in servicing the dry battery or one that is drained after the holes are filled with battery water is to close the battery cover again. The closure should be reinforced with glue using plastic glue or a hot glue gun or sealant to make it stronger. This is because once the cover is opened, it cannot close perfectly like before without using glue. Check while gluing to ensure that all parts close perfectly so that no air can enter or exit.

Charge the Dry Battery

After the dry battery cover is perfectly closed, you can charge the battery or refill the electrical power in the battery. There are two methods commonly chosen by workshops to charge the battery, namely the jumper method and the charging or battery charging method.

1. Charging the battery using the jumper method

The jumper method is sometimes chosen by workshops to charge the battery. The tools needed for the jumper method are another battery that is still working well and optimally. The method of charging with the jumper method is not too difficult because you only need to connect both batteries with cables.

Make sure that the position of both cars is close enough to facilitate the connection of the jumper cables. Connect the positive terminal of battery A to the positive terminal of battery B. Meanwhile, the negative terminal of battery A is connected to the negative terminal of battery B. Ensure that both are securely attached. Next, start the car engine and wait for about 30 to 60 minutes.

2. Charging the battery using the charging method

The charging method usually uses a special tool consisting of an adapter or can also use a transformer like the one used in phone and laptop chargers. This method is one of the most commonly used in various car workshops. The tools used for charging have a larger current capacity, so the charging process does not take long.

Check the Battery Performance

If all the above methods have been carried out, the next thing to do is to check the battery performance. To determine whether the battery performance is satisfactory, use a special measuring tool. The measuring tool is useful for knowing whether the dry battery has been sufficiently charged or not.

If the method of repairing the dry battery above is successful for your battery, then you should keep the car running for 30 minutes. To keep the battery in prime condition, you should periodically warm up the car.

Tips Sahabat