Tips for Driving on Descending Roads to Prevent Brake Failure
Driving downhill may seem easy because the car moves by itself, but this is where the brakes work the hardest. On long descents, the brakes that are continuously pressed become very hot, lose grip, and eventually the pedal can no longer hold back the vehicle's speed. This condition is known to drivers as brake failure.
Don't worry, brake failure on descents can be prevented. The key lies in habits before and during descending, such as choosing the right gear, controlling speed, and using the brakes correctly.
This article discusses why brakes can fail, lessons from three accidents on descents, and practical steps you can apply when driving downhill.
Why Brakes Can Fail on Descents
Brakes convert the vehicle's kinetic energy into heat. On flat roads, that heat dissipates quickly, whereas on long descents, the brakes continue to work, causing heat to build up faster than it can be released. As a result, a phenomenon known as brake fade occurs, which is a drastic decrease in braking power.
Several factors that make brake fade occur more quickly:
- Continuous braking.
The pads and discs or drums do not have time to cool down. - Old brake fluid.
Brake fluid absorbs water over time, lowering its boiling point. When it boils, steam bubbles form in the lines and the pedal feels soft or sinks. - Overloading.
Heavier vehicles store more kinetic energy, so the brakes have to work much harder. - Thin pads or problematic brake systems.
In trucks and buses with air brakes, insufficient air pressure also causes the brakes to not function optimally. - Too high a gear.
Without the help of engine braking, the entire braking load falls on the main brakes.
The last point is often forgotten by drivers, even though it is the easiest to control.
Lessons from Three Accidents on Descending Roads
The following three accidents occurred in different locations and conditions, but all involved heavy vehicles losing control on stretches of road that required extra braking.
-
Chain Collision at KM 92 Cipularang Toll Road (2024)
On November 11, 2024, around 15:15 WIB, a truck carrying cardboard collided with the vehicle in front of it at KM 92 Cipularang Toll Road heading to Jakarta. About 17 vehicles were involved, one person died, four were seriously injured, and 23 sustained minor injuries. This incident was due to driver negligence caused by brake failure and overloading, source Korlantas.
-
Descent Accident in Rapak, Balikpapan (2022)
On January 21, 2022, in the morning, a truck loaded with about 20 tons slid down the Muara Rapak descent in Balikpapan and then crashed into vehicles stopped at a red light. About 20 vehicles were involved, consisting of six cars and 14 motorcycles, and five people died. This incident was due to a malfunctioning brake pump that caused brake failure and loss of control.
-
Tourist Bus Accident in Wonosobo (2020)
On September 30, 2020, in the afternoon, a tourist bus coming from the direction of Dieng lost control on the long descent of Kahuripan Village, Garung District, Wonosobo. The bus crashed into several vehicles in front of it.
What is the common thread?
Investigations into each case highlighted different factors, ranging from non-functioning brakes, heavy loads, to speed. However, all three showed the same thing: once the main brakes can no longer hold back the vehicle's speed on a downhill path, the driver has almost no options. Therefore, the first crucial step is to use a low gear from the start of the descent, so the engine helps slow down and the brakes do not work alone.
Use Low Gears and Engine Braking
Engine braking is the slowing effect that occurs when the engine is running without additional fuel. The lower the gear used, the stronger the braking effect. This way, the vehicle's speed is controlled without having to continuously press the brake pedal.
Manual Transmission Cars
- Downshift before the descent begins, not after the vehicle is already speeding.
- A simple guideline: use the same gear as when you were climbing that road. Steep descents usually require gear 2 or 3.
- Avoid downshifting too aggressively at high speeds, as excessive engine RPM can damage the engine and cause the drive wheels to jerk.
- Do not press the clutch or shift to neutral while coasting. Engine braking is lost and control is reduced.
Automatic Transmission Cars
- Shift the lever to position L, 2, or 3, or use manual mode (tiptronic or paddle shift) to hold the gear in a low position.
- In hybrid and electric cars, select regenerative braking mode (e.g., mode B) if available.
- Do not shift to N while descending. Besides eliminating engine braking, this habit is dangerous if the brakes suddenly fail.
The correct gear position instructions for each car may vary, so make sure to read the vehicle's manual.